3W MR16 RGB Globes

Aussie Pythons & Snakes Forum

Help Support Aussie Pythons & Snakes Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Status
Not open for further replies.

Skitzmixer

Well-Known Member
Joined
Aug 19, 2010
Messages
483
Reaction score
1
Location
Cranbourne, Victoria
Just browsing around the interwebs when i stumbled across the 3W MR16 RGB globes.
Has anyone tried them in their enclosure before?

If not i'll give them a try and report back to everyone :)
 
Last edited:
For lighting they will be ok. For heat, they won't work as are an led
 
yeah sorry should of mentioned that, not after heat at all.. just for lighting..
I'd like to know how bright they actually are.. if anyone knows?
 
yeah sorry should of mentioned that, not after heat at all.. just for lighting..
I'd like to know how bright they actually are.. if anyone knows?

The white, green and yellow shades should be really bright. But being that its got 60degree optics it will be a bit of a spotlight.

(Aquarium people keep 30degree optics 8-9 inches(20ish cm) off the water surface to get a 4x4inch (10ish cm) covering at 12inches (30ish cm) deep.... If that gives you any sort of idea? )


*Edit I set a mr16 light up 30cm from my wall, the majority of the light covered about 8cmx8cm with 180LUX. From a 3w 60degree Blue MR16.
 
Last edited:
The white, green and yellow shades should be really bright. But being that its got 60degree optics it will be a bit of a spotlight.

(Aquarium people keep 30degree optics 8-9 inches(20ish cm) off the water surface to get a 4x4inch (10ish cm) covering at 12inches (30ish cm) deep.... If that gives you any sort of idea? )


*Edit I set a mr16 light up 30cm from my wall, the majority of the light covered about 8cmx8cm with 180LUX. From a 3w 60degree Blue MR16.


wow thanks for the write up! Much appreciated. I might give it a shot, at least then i can show other people what its like with some photos. I'll place the globe in the middle of my 4 foot enclosure, hopefully it'll give a nice glow and taper off towards the sides of the enclosure :)
 
Well, I just went and took a picture of two sitting on top of a 4foot tank... (GU10's instead of MR16's... Because that's what was laying around in the shed.)

576376_502855183069989_602163842_n.jpg


As you can see, its very much a spotlight effect. Super intense under the lights themselves but there is near no light spill into the surrounding area.

If you need anymore info on these kinds of lights... I'm stalking this thread.
 
Last edited:
I see what you mean by the 'spot light' effect. I set my lights up last night and it didnt quite have the tapering off effect i was hoping for, but overall its not to bad. These are just the MR16 globes, i'll eventually get an LED globe for them as i dont want it to create heat its more for just lighting. I still need to test it a bit though as the little boxes i've got the globes in doesnt have any air flow so im not sure how hot it will actually get if i leave it on for a while. I know these MR16 globes get hot really, really quickly, would of been within a few minutes if that i could feel the heat from it.


2012-12-19 21.28.37.jpg2012-12-19 21.28.30.jpg

Once these globes arrive i'll put another picture up and to show you how it all looks.

PS the enclosures not finished yet, i still need to bead up along the joints (to seal it) and add the glass rails etc.
 
still woulkd look sweet with a gtp under each globe :)

@Tehmwak- how do you have a big nice tank like that just laying around..lol If i have space i need to fill it lol :(
 
still woulkd look sweet with a gtp under each globe :)

@Tehmwak- how do you have a big nice tank like that just laying around..lol If i have space i need to fill it lol :(

Thats the plan :) I have one at the moment to put in the top enclosure but he's a got a while to go before he can be upgraded :)
 
@Tehmwak- how do you have a big nice tank like that just laying around..lol If i have space i need to fill it lol :(

I'm slowly getting out of keeping saltwater fish... Which means I've got a few empty tanks sitting around. <.<
(Which is also why I've got about 032973254794-852379-35839-58-293 of every type and colour of light laying around...)
 
I see what you mean by the 'spot light' effect. I set my lights up last night and it didnt quite have the tapering off effect i was hoping for, but overall its not to bad. These are just the MR16 globes, i'll eventually get an LED globe for them as i dont want it to create heat its more for just lighting. I still need to test it a bit though as the little boxes i've got the globes in doesnt have any air flow so im not sure how hot it will actually get if i leave it on for a while. I know these MR16 globes get hot really, really quickly, would of been within a few minutes if that i could feel the heat from it.


View attachment 274687View attachment 274686

Once these globes arrive i'll put another picture up and to show you how it all looks.

PS the enclosures not finished yet, i still need to bead up along the joints (to seal it) and add the glass rails etc.
Maybe mounting in a corner and directing towards opposite corner would produce better light
 
I see what you mean by the 'spot light' effect. I set my lights up last night and it didnt quite have the tapering off effect i was hoping for, but overall its not to bad.

View attachment 274687View attachment 274686

Once these globes arrive i'll put another picture up and to show you how it all looks.

With the LED ones you *Might* be able to remove the lens and have it spread better, not perfect but better.
 
yeah that looks wicked! How'd you do that?

I took the lens off the LED.

- - - Updated - - -

These are 3x1w GU10's. Not MR16's... But the light output is close enough to the same. The light output will be near identical as well.

181802_505037789518395_938958054_n.jpg


Now, when you take the lenses off with these particular globes... If you don't either replace the thermal paste with thermal cement or something the two parts eventually come apart.

576488_505037709518403_329525553_n.jpg


This is the difference in spread between the two globes sitting next to each other.

428802_505037649518409_1803289884_n.jpg


If I had the exact globes you are getting, I'd do either a step by step or a short video... But its easy to figure out with a couple of seconds inspecting the one you get.

If you have any questions. Let me know.

- - - Updated - - -

As you can see, the white is super bright but a complete spotlight. However the blue covers most of the wall area but is less intense. Its a tradeoff.
 
Looks pretty straight forwrd. I'll give it a shot once the globes finally arrive :)

Looking forward to seeing what it looks like. Thanks :D
 
Status
Not open for further replies.

Latest posts

Back
Top